Dance Top Picks

Woodworking Blog

Board Basics: How to Make an End Grain Cutting Board

End grain cutting boards might look complicated, but they are actually quite simple to make when you understand the principle behind them. As Wilbur Pan wrote in his post Board Basics: Cutting Board Design Considerations, cutting boards are easy to make and make great gifts. They can be as simple or elaborate as you want, using contrasting woods to form unique patterns. I’ll show you the steps for how to make an end grain cutting board that is beautiful and will last years.

A cutting board made out of locally harvested maple

End grain vs. edge grain

Chefs prefer end grain cutting boards because they have a kind of self-healing feature built in. When a knife blade goes into the board, it separates the wood fibers instead of severing them. That allows the fibers to go back together without any damage done. The board will get marked up over time with use, but wood will not be removed, as is the case sometimes with edge grain boards.

maple board detail

Wood selection

Dense woods with closed grain — species such as maple, walnut and cherry — work best. Woods with open grain, such as oak or ash, can allow bacteria to collect in the openings, making the board hard to keep clean.

walnut board with maple butterflies

Walnut is also great for cutting boards. This one features maple butterflies.

Steps to making an end grain cutting board:

1. Mill the wood

Using the standard methods for squaring up wood, mill your lumber to about 1 ½” thick. This measurement will be used to establish the length of the cutting board. If you are using different species of wood, mill all the wood for the cutting board at the same time so it will all be the same thickness.

maple board

It all starts with a board, like this 8/4 piece of maple.

2. Rip the wood

Using a table saw, rip the wood to width. This is where you can get creative. Make all the pieces the same width to create a checker board pattern. Rip the pieces to different widths to make more complex patterns. I like to use three different widths, such as 2 ⅛”, 1 ⅛” and ⅝”, a technique I learned from Marc Spagnuolo, a.k.a. The Wood Whisperer.

maple  board ripped to width

The wood is ripped to different widths to make an interesting pattern.

3. Glue up a panel

Arrange the pieces to create a pattern. Using at least a couple good clamps, glue the pieces side to side to create a panel. It’s important to make the panel as flat as possible to avoid too much sanding and planing later. Here is my process for ensuring the panel is glued up as flat as possible.

4. Set-up for gluing success

To make the panel flat, I use a few accessories when doing the glue-up. First, I milled a couple of pieces of wood to act as runners to help keep all the pieces flat and to elevate them to make it easier to clamp them. I drape a piece of wax paper over the runners to keep glue squeeze-out off of the table top and the clamps. I use two cauls – pieces of wood with a very slight amount planed away from each end. When the clamps go on, the cauls act as a spring to even out the clamping pressure.

glue set up

These two pieces of wood are exactly the same height so they keep the panel flat during glue-up.

glue set up wax paper

Wax paper keeps glue squeeze-out off the table and clamps.

glue set up with clamps

Cauls help distribute the clamping pressure evenly.

In my next post, I’ll flatten the panel, crosscut it into strips and glue it back together again. I will also discuss edge treatments and handles, then talk about finish options.

Learn from the best instructors, check out our woodworking classes here!



How do I get to the rest of this post?

Ed Motter

Hi, please be sure to mention what glue you use since it must not be toxic. Thank you.


Any glue used will be nontoxic, but just about any woodworker worth his or her salt (not to mention in possession of the tools needed for this) will already own a water safe PVA or poly glue…which are both food safe when cured.


I didn’t understand, or it wasn’t clear on which way to rip the wood. Thanks


When you rip wood, you cut along the grain. When you cross cut, you cut across the grain. There’s only one direction to go in each method.

Does that help?


It looks to me like your instructions are building the cutting board from the side grain, and not the end grain. To use only end grain, you would need to cut 50-100 or more pieces the exact same width off the end of each piece. Am I missing soething here ?

RL Casad

Dave. Part 2 will probably cut this board into equal widths and rotate 90 Deg to expose the end grain and then reglue. By reversing some of the cut boards an interesting pattern will develop


I’m betting that in the next step, after the ripping and gluing, the poster will show the ripped and glued stock will then be cross cut.


Thanks for the comments! Ed, the glue I use for cutting boards is Titebond III, which is waterproof and rated as safe for food. In the next installment for this project, I’ll describe the process for ripping the wood so that it takes just one more glue-up to put the board together. You definitely don’t have to cut individual squares of wood. All will be revealed! Thanks, Mitch


Thanks Mitch for sharing your wonderful tips. Very much appreciated!


Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply