Sewing Blog

3 Ways to Mark Darts on Fabric

Before you actually get to sewing a garment, you need to transfer the pattern markings to your fabric. Properly marking the darts and sewing them as indicated can make all the difference in achieving a well-fitting garment. So what’s the best way to mark darts? Here are three popular options.

A View of Darts

Method 1: Tailor’s tacks

Tailor’s tacks are my go-to method for marking darts in most any fabric. Tailor’s tacks are strands of thread looped between the fabric pieces, and they remain on the spot to indicate a dot or other marking.

I try to do them in an assembly line approach, doing all the tailor’s tacks once the garment is cut out. That way, I can set my project aside knowing the patterns markings have been applied. Plus, if the pattern pieces are shifted or removed, your marks are in the right place.

Step 1: Prepare the needle and thread

making tailors tacks

To start, thread your needle with a long strand of thread, doubled as shown above. Don’t tie a knot, as the thread needs to slip through the fabric. Use a starkly contrasting color, which makes the tailor’s tacks easy to see as you are sewing. 

Step 2: Pull the needle through the fabric

pull the needle through to make a loop

Use the needle to pull the thread down through the pattern, through both layers of fabric and then come up on the other side of the dot, leaving about a 2″ tail of threads on the top layer (which is visible to you).

You can do the same again, still not cutting the thread, creating a loop,   If you flip your fabric  pieces over, you will see the threads there making a small X, marking the dot position. 

Back side of tailor's tacks

Step 3: Cut the loops

tailor tack cut loops

Once you’ve completed all the tailor’s tacks on a particular pattern piece, go through and cut all the loops in half. This releases the threads on the surface layer so that now the dot is indicated by strands of thread that run through both layers of fabric.

Step 4: Snip the threads between layers of fabric

Tailortack cut between layers

Almost done — time to snip the threads, creating a tailor’s tack on each of your fabric pieces.

Pull the fabric gently apart and snip through all the threads between the two layers of fabric.

Note that the tacks on the bottom layer of the fabric are more securely fixed  because they are pulled against the fabric. As long as you have about 2″ of thread, it will stay in the fabric when snipped. You do have to be a little bit careful, as there is nothing holding these threads in the fabric.

dart marked with tailor's tacks

Tailor’s tacks are a great way to mark long vertical darts, as well as sleeve markings, corner points or collar matching. Once the tacks are in place, you can use chalk to mark the stitching line on the wrong side of the fabric. 

For delicate fabrics that might be permanently marked or develop holes, there are other options you can use. 

Method 2: Transfer or tracing paper

Transfer or tracing paper can be used with a tracing wheel to mark on your fabric. Using this marking method requires testing on your fabric scraps before moving to your actual pattern pieces. 

There are many types of transfer paper available. Some are coated with chalk or wax, and they come in a variety of colors. I’ve seen a version that’s similar to the disappearing ink marking pens.

mark dart with chalk

To transfer the markings, first pay attention to whether the pattern pieces are on the right or wrong side of the fabric. In the photo above, the right side of the fabric is on the outside, facing the pattern paper and the table surface. The transfer paper then goes in between the layers of fabric, and is folded so that the marking side of the paper is against the wrong side of the fabric.

Run the tracing wheel over the pattern piece to mark onto the fabric. It helps to have a firm surface, such as a cutting mat, under the fabric so that the tracing wheel can be pressed firmly. You can mark the entire dart stitching line or just mark X’s at the dots to indicate those.

chalk marked dart completed

On this denim fabric, I chose an orange paper, which provides a good contrast with the denim fabric. On the inside it marks the dart shape. A drawback to this method is that it can create an impression or pinholes, especially if you need to use a lot of force to get the transfer onto the bottom layer. One way to avoid this is to separate the fabric, such as two skirt back pieces, and mark each separately, which would require less pressure.

Method 3: Pin and pencil

The last method requires no special tools other than a pencil. This works best on items with small pattern pieces, like children’s clothes, toys or bags. Note that you always need to have the wrong side of the fabric visible to mark this way.

using pin to mark dart

To mark the dots of a dart, you can put a pin through the pattern into the fabric, and then lift up and mark a small dot with a pencil at the point. If you’re cutting out a double layer, leave the pin poked through the fabric, turn it over and mark the other side as well.

darts marked with pencil

The pin and pencil method works best fabrics with like cotton or linen that are easy to handle and where a tiny pencil dot won’t show once the dart is sewn up. You can use colored pencils to make the marks less visible based on the color of your fabric. 

Which method do you prefer?

Patternmaking + Design: Creative Darts & Seam Lines

Everything You Need to Know About Darts

Join popular instructor Suzy Furrer and learn how to manipulate darts of all kinds for an even better fit.Get the Class

5 Comments

cat

The easiest way is to use a heat sensitive fixion (SP) pen and make a dot right thru the pattern. Then when you are done sewing you iron it off.

Reply
Linda G

An extra tip for working with tailor’s tacks is to not cut the loop before separating the fabric layers. Make the tails longer than the loop, so they won’t pull through if you accidentally pull to the end of the loop. This helps to avoid the possibility of the threads pulling out of the fabric as the intact loop provides a bit of a stop when separating the fabric layers. You can then cut the threads between the layers, leaving matching thread marks on both pieces, while only having to cut the tailor’s tack once when separating.

The pin and pencil method also works if you use chalk, a fabric pencil, or a disappearing marker. These other marks may be easier to remove than a graphite pencil mark, if necessary. As always, test the marking method on a scrap of your fabric first.

Reply
Abby

Photos of the tacking method would be helpful

Reply
magnoliasouth

I’m on my phone so I may not be seeing this correctly but doesn’t that ruin a pattern so that it cannot be used again?

Reply
ili

Yes Magnoliasouth, that is what I am thinking, considering the so much thin papper that is coming with patterns!!

Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply