Dance
Dance Top Picks

Knitting Blog

How to Block Shawls for a Sharper Finish

When you knit a shawl, you might notice that while you’re stitching it and even when you bind off, the shawl looks all scrunched up. Triangle shawls look more like big blobs than like a triangle, and you can’t quite make out those gorgeous yarn overs that you stitched.

Campside Knitted Shawl

Pictured above is Campside by Alicia Plummer, a shawl I recently completed. See how bunched up all the stitches look, even the stitches that are far away from the needle? There’s an easy way to solve all those problems: blocking.

Sometimes I skip the blocking step (don’t call the knitting police, please), but I never skip it for shawls. Blocking gives shawls so much shape, and it really brings out the stitch pattern.

The Knitter’s Guide to No-Fuss Finishing

A Knitter’s Guide to No-Fuss Finishing

Learn essential finishing techniques you can use to bring out the true beauty in any knitting project.Download for FREE

Blocking tools

To block your shawl, you’ll need:

These supplies are certainly not required, but they do make blocking your shawl easier:

How to block your shawl

Step 1: Soak

After you bind off and weave in the loose ends, soak your shawl in a basin or sink filled with lukewarm water.

Washing a knit shawl

If you’d like, you can also add a soap like Soak Wash to the water. This is a great idea if you are like me and tend to knit in environments where your yarn might get dirty, like outdoors or in breweries!

Push the shawl into the water and squeeze it, soaking it completely with water. Allow the shawl to soak for about 15-20 minutes.

Step 2: Dry

After 15-20 minutes, drain the sink or basin. Gently squeeze water out of the shawl, being careful not to twist or wring it. (That can pull on the yarn, and we don’t want to do that!)

Washing a knit shawl

I also like to push the shawl up against the sink and push down on it with the palms of my hands to remove excess water.

Blocking a knit shawl

Place the shawl in a towel, then roll up the towel. Push down gently to squeeze even more water out of the shawl.

Step 3: Spread it out

Remove the shawl from the towel and spread the shawl onto a blocking surface. Some surface options include:

  • Blocking mats
  • The kitchen table
  • A fresh towel
  • A bed

Just be sure the surface of whatever you use is clean.

If you’re using blocking mats and don’t have enough surface to accommodate your shawl, you can move the puzzle-like pieces around so that they form the shape of your shawl. For example, if your shawl is a triangle shawl, arrange the blocking mat into a triangle shape.

Step 4: Block with pins and/or wires

You can choose to use just blocking pins, just blocking wires, or both.

Using blocking wires

First identify a couple of spots where you want the shawl to be straight. Examples might be the spine of the shawl or the long edge across the top of the triangle.

Blocking knit shawl with wires

Thread the blocking wires in and out of the shawl, moving them in and out of the stitches. Spots where you have yarn overs are great for threading the wires. For example, if your spine is made up of two yarn overs like mine is, you can thread blocking wires through both yarn overs to really straighten the spine.

Using blocking pins

Starting at the center of the shawl, pin the center spine to the surface. Be sure to pull the spine on the top and the bottom. Check the pattern schematic for the length and stretch the shawl to that length.

Pinning knit shawl corners

When the center spine is in good shape, pin the outside corners of the shawl. If your shawl is a triangle shawl or a shawl that has distinct points, make sure you pull the points out and pin them to shape the corners.

Blocking knit shawl

Place pins along the edges of the shawl, pulling the shawl to even out the stitches as you work. You may need to shift some of the pins around as you go. Just keep adjusting until you’re happy with the shape of your shawl.

Using blocking pins and wires

If you have both pins and wires, you can mix these two approaches to block your shawl even more accurately. You’ll still want to use wires and pins at the shawl spine, and place pins at the shawl corners.

Pinning blocking wires

For the edges of the shawl, use blocking wires for shaping and use pins to keep everything in place on your surface.

Let the shawl sit out the blocking surface until it dries, then remove all the wires and pins. Even after it’s dry, you can always re-block it if you’re not happy, but you’ll probably be too excited to do that!

Do you have any tips for blocking a shawl? Tell us about your blocking tools and techniques in the comments!

The Knitter’s Guide to No-Fuss Finishing

A Knitter’s Guide to No-Fuss Finishing

Learn essential finishing techniques you can use to bring out the true beauty in any knitting project.Download for FREE

8 Comments

Yvonne

My question is this: Once you’ve knitted a shawl which you gone through the trouble of blocking, and you desire to give it as a gift, all of that painful shaping and blocking is gone once the recipient washes it. What’s a remedy for this???

Reply
Audrey

Gently steam iron the article with a clean sack cloth tea towel over it. For the most part that will make sure it will hold it’s shape.

Reply
Anita Fuehrer

I stand on the rolled up towel to force water out of the shawl. You would be surprised how much water you can get out of it. If the yarn is bulky, you might need to do it a couple of time (more wet towels!) but the end result is a faster drying shawl.

Reply
GoMovies

Use blocking wires for shaping and use pins to keep everything in place on your surface.

Reply
Dee

Waiting for the shawl to dry is frustrating, and there are times when you need the shawl NOW. You shouldn’t use heat, but you can get a totally dry shawl in a hurry. Use a big fan. A box fan or any fan that has a high setting works. I block on my bed, so I put the fan on a chair next to the bed, point it at the shawl and turn it on “High”. The shawl will be dry in less time than you would believe. Then I can sleep in my own bed and not have to work around the blocking shawl. It’s like magic!

Reply
photoshop online

Thanks for this beautiful, useful tutorial! Your instructions with the up-close images are so clear.Its good to see such a marvelous information.I hope you will also share more information in future.Thank you.

Reply
abcya

Oh, great, your article gives me useful information and a fresh perspective on the subject.

Reply
Trish Hilton

I was told that on the finished shawl you should pin it out to the correct size then cover it with a wet clothe and leave until the clothe is dry

Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Leave a Reply